TXC OE Series OCXO 14.6 x 9.6 mm 10 – 54 MHz

SKU: TXC-OE-SERIES
Category: ,

10 to 54 MHz Stratum 3E OCXO, +/-5 to +/-10 ppb over -40 to +85 C, 3.3 V LVCMOS, 14.6 x 9.6 x 6.7 mm, phase noise floor -164 dBc/Hz.

Available on backorder

Request Price & Availability

Pricing, lead time and bulk discounts are quoted per order — send us your part numbers and quantities and we will reply within one business day.

Email us for a quote

Description

The OE Series is TXC’s full-size ThermSym oven-controlled oscillator, and it is the part to reach for when a design has to hold a frequency reference through a temperature swing rather than simply survive it. Output frequency spans 10 to 54 MHz with +/-5 to +/-10 ppb stability over -40 to +85 C, and a 3.3 V LVCMOS output drives standard timing logic without an external buffer.

Where the OE Series fits in a timing chain

At 14.6 x 9.6 x 6.7 mm the OE is the largest of the four TXC OCXO families, which is also why it has the most thermal mass to work with. The datasheet targets Stratum 3E synchronisation, base station DU and CU line cards, AAU and 5G RRH units, and phase holdover. In those designs the OCXO is not the clock the board runs on day to day; it is the reference that keeps the board’s time error inside budget while the network reference is lost.

Aging is quoted as +/-1 ppb per day, +/-0.3 ppm in the first year and +/-1.5 ppm over ten years, with an all-causes figure of +/-4.6 ppm across ten years of operating conditions. That all-causes number is the one to design the holdover budget around, because it already folds in temperature, load, supply and ageing rather than asking you to stack worst cases yourself.

Phase noise and warm-up

TXC publishes a phase noise curve at 10 MHz: -86 dBc/Hz at 1 Hz, -119 dBc/Hz at 10 Hz, -140 dBc/Hz at 100 Hz, -157 dBc/Hz at 1 kHz, -162 dBc/Hz at 10 kHz, -163 dBc/Hz at 100 kHz and -164 dBc/Hz at 1 MHz. For microwave transmission and radar-adjacent work the close-in numbers matter more than the floor, and the -119 dBc/Hz at 10 Hz is the figure that separates an OCXO from a good TCXO in a phase noise plot.

Warm-up is 3 minutes maximum with a 750 mA surge, settling to 200 mA at 25 C. In a line card that is powered continuously this is irrelevant; in battery or PoE equipment it sets how long after power-up the node can be trusted as a reference.

Options that change the part number

TXC builds this family to the frequency the customer specifies, so the orderable code depends on frequency, stability grade and temperature option. Three options appear in the datasheet and should be settled before a quotation is issued: a +/-3 ppb stability grade, a 95 C upper operating temperature, and an AFC input (0 to 3.3 V control voltage, +/-3.6 to +/-5 ppm pulling range, 1 to 3 percent linearity) for locking the oscillator to an external reference. The OE is supplied sourced to order; availability and lead time are confirmed with each quotation, and the frequency and option set are fixed at that point rather than assumed from a catalogue code.

Grades published for this package

The series letter on these parts names a package, not a single stability class. TXC lists the same package in more than one grade, and the electrical table further down this page belongs to the grade whose datasheet is linked above. A part can therefore carry this series letter and still differ in stability, upper temperature and frequency span, so the grade is fixed together with the frequency when the order is placed.

Grade Stability vs temperature Operating temperature Frequency span
ThermSym +/-20 ppb -40 to +85 C 10 – 50 MHz
Reliable (Hercules) +/-10 ppb -40 to +105 C 10 – 54 MHz
High stability (Chronos) +/-5 ppb -40 to +85 C 10 – 54 MHz

If the target design sits between two rows, send the frequency and the temperature range it has to survive to leon@vexelora.com and the grade will be quoted against that requirement.

Specification summary

Output frequency 10 – 54 MHz
Stability vs temperature +/-5 ppb min, +/-10 ppb max (+/-3 ppb on request)
Supply voltage 3.3 V +/-5%
Current, warm-up 750 mA max
Current, steady state at 25 C 200 mA
Warm-up time 3 min max
Aging, per day +/-1 ppb
Aging, first year +/-0.3 ppm
Aging, 10 years +/-1.5 ppm
All-causes stability, 10 years +/-4.6 ppm
Operating temperature -40 to +85 C (95 C on request)
Package 14.6 x 9.6 x 6.7 mm
Phase noise at 10 MHz, 1 kHz offset -157 dBc/Hz
AFC pulling range (option) +/-3.6 to +/-5 ppm over 0 to 3.3 V

Typical applications

  • Stratum 3E synchronisation
  • Base station DU and CU
  • AAU, 5G RRH and small cell
  • Phase holdover

Related TXC timing products

Send the frequency, stability grade and target temperature range to leon@vexelora.com for a quotation.

Specifications

Attributes Value
Brand

TXC

Condition

New / Original

Packaging

Standard export carton

Lead Time

Availability and lead time confirmed with each quotation

Warranty

12 months

Series

OE (ThermSym, high stability)

Output Frequency

10 – 54 MHz

Frequency Stability vs Temperature

+/-5 ppb min, +/-10 ppb max (+/-3 ppb on request)

Supply Voltage

3.3 V +/-5% (3.315 / 3.3 / 3.465 V)

Output Type

LVCMOS

Operating Temperature

-40 to +85 C (95 C on request)

Package

14.6 x 9.6 x 6.7 mm SMD, 6 pad

Warm-up Time

3 min max

Current Consumption

750 mA max warm-up, 200 mA steady state at 25 C

Aging

+/-1 ppb/day, +/-0.3 ppm first year, +/-1.5 ppm 10 years

Phase Noise (10 MHz)

-86 dBc/Hz @1 Hz, -119 @10 Hz, -140 @100 Hz, -157 @1 kHz, -162 @10 kHz, -164 @1 MHz